oak pegs

[Axholme Ferreter 0]

I got hold of a couple of solid kitchen cabinet doors from someone 'refurnishing' their kitchen (more money than sense), cut some pegs out of the frame and loads out of the centre pannel.

All the best

AF

[Tyla 3,179]

if you get stuck then let me know, i may be able to help you out

[Leeview 791]

Hi Tomo go to your nearest undertakers. All coffins are made from oak they are usually glad to get rid of all the off cuts. Thats were i get mine from.

I used to assemble and polish coffins and there oak veneered chipboard, with a little bit of oak moulding pinned on top and bottom

Y.I.S Leeview

[COMPO 54]

what you need is a chainsaw and an oak tree!

[trader 0]

ok chaps , i want to make a shed load of pegs,

 

what im after is oak planks, about 1/2 inch thik and about 6 or 7 inch wide. then i can cut streight across evry inch, then cut that bit across the diaganal . a quik sand and a drill a hole , job done.

 

went to b&q , no good.

 

so where would i find wood of this type

try wood lots /woodnet

[The one 8,463]

What about scafolders plank's are they made out of hardwood though? easy enough to borrow a couple and rip them up

[shepp 2,285]

What about scafolders plank's are they made out of hardwood though? easy enough to borrow a couple and rip them up

 

No softwood mate, would cost the earth if they were hardwood.

[DUCKWING 302]

WELL LADS ,

 

IVE HAD A CHUCKLE READING THIS THREAD ..............

 

LEEVIEWS RIGHT , MOST OAK IS VENEERED AS ITS EXPENSIVE .... VERY EXPENSIVE

 

SAME AS MOST HARDWOODS ......... OAK USUALLY RUNS FROM £ 15 A CUBIC FOOT FOR RECLAIMED UP TO £ 45 FOR TOP GRADE ENGLISH OAK A CUBE ................

PERSONALLY I THINK AXHOLME HAS THE RIGHT IDEA ,........... STOP AT EVERY SKIP AND HAVE A RAKE THROUGH ANY OLD FURNITURE ETC ... THE BOARDS MIGHT BE VENEER BUT THE LEGS RARELY ARE ON FURNITURE ....... KITCHEN CUPBOARD DOORS ARE OK HOWEVER MANY ARE MADE BUTCHERS BLOCK STYLE AND UNSUITABLE FOR GOOD PEGS AS THEY HAVE WEAK SPOTS DUE TO THE AMOUNT OF JOINTS

IVE MADE HUNDREDS AND HUNDREDS IN A HOUR .. MANY TIMES ....... OFTEN TURNING OUT A THOUSAND PEGS IN TWO HOURS WITH A GOOD TABLE SAW AND MY JIGS

 

ALL THE BEST

 

DUCKWING

[TOMO 26,034]

IVE MADE HUNDREDS AND HUNDREDS IN A HOUR .. MANY TIMES ....... OFTEN TURNING OUT A THOUSAND PEGS IN TWO HOURS WITH A GOOD TABLE SAW AND MY JIGS

 

 

 

thats good to hear duckwing, i will pm you my adress

[micky 3,325]

IVE MADE HUNDREDS AND HUNDREDS IN A HOUR .. MANY TIMES ....... OFTEN TURNING OUT A THOUSAND PEGS IN TWO HOURS WITH A GOOD TABLE SAW AND MY JIGS

 

 

 

thats good to hear duckwing, i will pm you my adress

see Little Llyod, hes got a good sized lump that sits on his neck doing nowt

[j davies 8]

ok chaps , i want to make a shed load of pegs,

 

what im after is oak planks, about 1/2 inch thik and about 6 or 7 inch wide. then i can cut streight across evry inch, then cut that bit across the diaganal . a quik sand and a drill a hole , job done.

 

went to b&q , no good.

 

so where would i find wood of this type

 

tried them and dont like them lol i use hazel wood works well in the frost and they are very very hard the wood you get from shops i find is not that good they want go in the ground easy every net i get with pegs i cut them off and fit home made hazel ones