Pulsar C50 comes good

[si brown 8,486]

6 minutes ago, FOXHUNTER said:

He took it off today and put back on ensuring mounts were tight. Still wont zero so going back on Monday , hes really pi$$ed off. Shooting low at 90 yards so adjusted and ended up shooting 7 inches high ??

If it’s the same as the thermion scopes for zeroing the click values change dependent on the magnification your using… on one setting it might be 1/4 ma and and 1 ma per click. 
I can’t remember as it’s been a while since I zeroed mine but it sent me round the bend till I sussed out what was what. 

[FOXHUNTER 5,021]

55 minutes ago, si brown said:

If it’s the same as the thermion scopes for zeroing the click values change dependent on the magnification your using… on one setting it might be 1/4 ma and and 1 ma per click. 
I can’t remember as it’s been a while since I zeroed mine but it sent me round the bend till I sussed out what was what. 

This has the 1 shot zero which should be simple. Move the x and y coordinates on to point of impact and job done ...not for him

 

 

 

 

[si brown 8,486]

1 minute ago, FOXHUNTER said:

This has the 1 shot zero which should be simple. Move the x and y coordinates on to point of impact and job done ...not for him

 

 

 

 

Yeah my thermal has the same set up but the clicks don’t match up when on the wrong mag, I was ready for smashing the Fcukin thing up till I sussed what was going on. 

[FOXHUNTER 5,021]

21 minutes ago, si brown said:

Yeah my thermal has the same set up but the clicks don’t match up when on the wrong mag, I was ready for smashing the Fcukin thing up till I sussed what was going on. 

I dont understand how mag makes any difference....the whole point of 1 shot zero is move the reticle on to point of impact....and job done. Hes tried 3 times to zero using 40 rounds and no further forward .

[ianm 2,594]

9 minutes ago, FOXHUNTER said:

I dont understand how mag makes any difference....the whole point of 1 shot zero is move the reticle on to point of impact....and job done. Hes tried 3 times to zero using 40 rounds and no further forward .

I don't know about the c50 but some digital scopes have to be zeroed on base mag or they won't hold zero. Worth trying before sending back. 

[FOXHUNTER 5,021]

On 02/02/2022 at 21:31, David.evans said:

https://youtu.be/fiJbJAhy9Eo

just learnt how to do this , took at 160 yards , spotted with the xq38 , when t to the scope and could not find it as I’d left the scope on x7

this is the one shot that’s layer on the trailer 

atb 

How did you zero yours David ? On base mag etc..

[si brown 8,486]

23 minutes ago, FOXHUNTER said:

I dont understand how mag makes any difference....the whole point of 1 shot zero is move the reticle on to point of impact....and job done. Hes tried 3 times to zero using 40 rounds and no further forward .

Dependent on mag they go up in .25 of min angle increments… just been saying to my lass about it cos if I was using shop ammo it would of cost me a fortune!

It tells you click values in top right corner but it was hard for me to see it during the daylight when I did it

[FOXHUNTER 5,021]

10 minutes ago, si brown said:

Dependent on mag they go up in .25 of min angle increments… just been saying to my lass about it cos if I was using shop ammo it would of cost me a fortune!

It tells you click values in top right corner but it was hard for me to see it during the daylight when I did it

I am just wondering if he never saved it correctly as no saved message was displayed.  Told him to try again and see if saved message appears ....if not maybe software problem. 

[si brown 8,486]

6 minutes ago, FOXHUNTER said:

I am just wondering if he never saved it correctly as no saved message was displayed.  Told him to try again and see if saved message appears ....if not maybe software problem. 

If he did it when it was one inch low and set it to one inch high.. 8 clicks at full value would of put it 7” high. 
if there was no horizontal drift then that’s the problem 

[FOXHUNTER 5,021]

2 minutes ago, si brown said:

If he did it when it was one inch low and set it to one inch high.. 8 clicks at full value would of put it 7” high. 
if there was no horizontal drift then that’s the problem 

I'm confused as no clicks involved just place little red cross on point of impact or am I missing something?

[si brown 8,486]

24 minutes ago, FOXHUNTER said:

I'm confused as no clicks involved just place little red cross on point of impact or am I missing something?

Moving it involves clicks be it digital clicks… click value can vary between .25-1/4” to 1/1”

[FOXHUNTER 5,021]

53 minutes ago, si brown said:

Moving it involves clicks be it digital clicks… click value can vary between .25-1/4” to 1/1”

Just spoke to him and think we've sussed it. He originally zeroed at 40yds , which is input in scope. Then when he changed it to zero at 100yds never changed the distance on the scope menu......doh.                             So will try again tomorrow and I reckon it will be right

 

[David.evans 5,323]

It will be FH , pity he didn’t tell you that to start with 

and the scope will not show a tick when coming out of zero , just make sure he holds the knob in till the screen changes 

atb 

[FOXHUNTER 5,021]

Well he has eventually got the scope zeroed ....now just need to get out and see what it's like.

[David.evans 5,323]

You out with him FH , or just your shadow