jetro 5,349 Posted August 13, 2020 Report Share Posted August 13, 2020 I'm going to be retiling the kitchen, bathroom and corridor soon, do I have to lift the old tiles or can I lay the new ones down over them Atb j Quote Link to post Share on other sites
Greyman 28,685 Posted August 13, 2020 Report Share Posted August 13, 2020 Feck me rusty you must love work, just dot and dab it with plasterboard, but if the tiles are stuck firm and straight I would recon it’s ok to go over them, have hacked off hundreds of bathrooms over the years and many of them had more than one layer of tiles on 1 Quote Link to post Share on other sites
jetro 5,349 Posted August 13, 2020 Author Report Share Posted August 13, 2020 Sorry lads. Meant to say just floor tiles. But thanks for the advice sofar Atb j 2 Quote Link to post Share on other sites
Greb147 6,809 Posted August 13, 2020 Report Share Posted August 13, 2020 14 minutes ago, jetro said: Sorry lads. Meant to say just floor tiles. But thanks for the advice sofar Atb j The four candle gag all over it this..... 2 Quote Link to post Share on other sites
Greb147 6,809 Posted August 13, 2020 Report Share Posted August 13, 2020 Roof tiles, wall tiles, floor tiles, scrabble tiles. Quote Link to post Share on other sites
Jonjon79 13,358 Posted August 13, 2020 Report Share Posted August 13, 2020 3 hours ago, jetro said: Sorry lads. Meant to say just floor tiles. But thanks for the advice sofar Atb j What's under the tiles Jetro? .......... Are they concrete floors or wood floors? 1 Quote Link to post Share on other sites
Squirrel_Basher 17,100 Posted August 13, 2020 Report Share Posted August 13, 2020 DONT ply it mate .It will lift trust me .Latex the floor if needed but don’t ply it out .Pva the surface when it’s dry and tile . 5 1 Quote Link to post Share on other sites
Squirrel_Basher 17,100 Posted August 13, 2020 Report Share Posted August 13, 2020 Ply has a bad habit of taking on moisture and if the Dpm isn’t spot on you’ve got a problem .Weve just done a floor in a huge house near Bath that some tiler thought was ok to ply . Only advice mate no need for the racist imogee. Quote Link to post Share on other sites
jetro 5,349 Posted August 13, 2020 Author Report Share Posted August 13, 2020 12 minutes ago, Jonjon79 said: What's under the tiles Jetro? .......... Are they concrete floors or wood floors? Concrete jonjon. Maybe I'd be just as well off to lift them and clean the adhesive as best I can. Atb j Quote Link to post Share on other sites
Squirrel_Basher 17,100 Posted August 13, 2020 Report Share Posted August 13, 2020 6 minutes ago, Rusty_terrier said: All mines are onto screwed down ply. All are absolutely fine. Why would it lift never seen anybody say that before ? I had a new bathroom done there that was wooden floors. Tiler told me to stick down 12mm ply before he started and have it screwed down so it wouldn't budge. This was only 6 month ago Done my downstairs bathroom and kitchen myself. 12mm ply screwed to f**k onto the floor tiles in top. None have moved in 6 years Your tiler was cutting corners mate .Bathrooms need to be decked out with cement board over T and G boards . Take it or leave ,no sweat here . Quote Link to post Share on other sites
Squirrel_Basher 17,100 Posted August 13, 2020 Report Share Posted August 13, 2020 1 minute ago, jetro said: Concrete jonjon. Maybe I'd be just as well off to lift them and clean the adhesive as best I can. Atb j Is it an old house mate pre 70s Quote Link to post Share on other sites
Squirrel_Basher 17,100 Posted August 13, 2020 Report Share Posted August 13, 2020 Tiles are easily lifted with an angled spade attachment to a Kango drill .Wear eye protection thou . 1 Quote Link to post Share on other sites
eggy74 31 Posted August 13, 2020 Report Share Posted August 13, 2020 Tile backer is a couple of quid more than ply and designed for the job, can be screwed down or laid on an adhesive (cement board). Ive used ply before and never had an issue, but i have also replaced loads of bathrooms with tiles on ply that have popped of as soon as i start gunning them up, also sometimes the laminated ply sheet itself has come apart. as above check for door clearances and appliances will fit if going on top. 1 Quote Link to post Share on other sites
Jonjon79 13,358 Posted August 13, 2020 Report Share Posted August 13, 2020 11 minutes ago, jetro said: Concrete jonjon. Maybe I'd be just as well off to lift them and clean the adhesive as best I can. Atb j If I was doing the job, I'd take up the old ones first - if there's only 1 layer of tiles down already and they're all sound, you could go straight over the top. It'll make the job quicker and cleaner. As has already been said, you might need to sort the clearance on a door or 2. If you take them up, depending how rough you leave the floor, you might want to put down a leveling compound before tiling - if you go that route, use a tilers primer (not PVA) over the new surface before tiling. Quote Link to post Share on other sites
jetro 5,349 Posted August 13, 2020 Author Report Share Posted August 13, 2020 15 minutes ago, Jonjon79 said: If I was doing the job, I'd take up the old ones first - if there's only 1 layer of tiles down already and they're all sound, you could go straight over the top. It'll make the job quicker and cleaner. As has already been said, you might need to sort the clearance on a door or 2. If you take them up, depending how rough you leave the floor, you might want to put down a leveling compound before tiling - if you go that route, use a tilers primer (not PVA) over the new surface before tiling. Thanks Atb j 1 Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.