jocky 198 Posted September 28, 2015 Report Share Posted September 28, 2015 How do you all carry you rabbit snares, with out them getting tangled up. Quote Link to post
CHEVINFOX 3,537 Posted September 29, 2015 Report Share Posted September 29, 2015 (edited) i used to put them in 5s and put a couple of them wire ties on them like this http://www.amazon.co.uk/dp/B0001IX2GU/ref=pd_lpo_sbs_dp_ss_2?pf_rd_p=569136327&pf_rd_s=lpo-top-stripe&pf_rd_t=201&pf_rd_i=B0055C1DEU&pf_rd_m=A3P5ROKL5A1OLE&pf_rd_r=0R0M380S6VTZ5BGQQ6RS Edited September 29, 2015 by CHEVINFOX Quote Link to post
J Darcy 5,871 Posted September 29, 2015 Report Share Posted September 29, 2015 This...... Quote Link to post
The one 8,467 Posted September 29, 2015 Report Share Posted September 29, 2015 If a big lot a 12 inch section of brush shaft with fifty snares on each section , a smaller job just put them over my wrist but I put the tealer and peg back threw the snare 1 Quote Link to post
MR TEA POT 1,287 Posted September 30, 2015 Report Share Posted September 30, 2015 Hands and arms 1 Quote Link to post
Fat-Ferret 857 Posted September 30, 2015 Report Share Posted September 30, 2015 If your using snares with tealers and pegs and put them on your arm they shouldn't tangle too easily Quote Link to post
Jarvis 277 Posted September 30, 2015 Report Share Posted September 30, 2015 Same way as 'the one' get group of fives or tens and put pegs back through wire and carry on wrist or I have a back pack with spare wires, pegs etc in if I have lots to carry. If you do them this way they are easy to count in and count out aswell. 1 Quote Link to post
stealthy1 3,964 Posted September 30, 2015 Report Share Posted September 30, 2015 I use a length of fence wire bent in a circle with the ends bent to make two hooks, circumference is between 9 and 12 inches, hang up in the motor, or on hooks in the shed, all I do is undo the hook at either end to remove a wire. Quote Link to post
mole trapper 1,693 Posted September 30, 2015 Report Share Posted September 30, 2015 I use a length of fence wire bent in a circle with the ends bent to make two hooks, circumference is between 9 and 12 inches, hang up in the motor, or on hooks in the shed, all I do is undo the hook at either end to remove a wire. Exactly! I put 25 on each ring, count them out, count them in, 25 out, break a twig in the hedge or bailer twine on the fence, eazy peezy. 1 Quote Link to post
The one 8,467 Posted September 30, 2015 Report Share Posted September 30, 2015 I just put two nails up just shorter than the length of brush shaft and hang them from that and lay them flat in the motor and when I've laid fifty just drop the brush shaft and I know if I don't pick up fifty I only have to go back and look in that bit of land with fence snares I just stick a bit of weed in the wire at the next fence post same with when the snare line runs out Quote Link to post
jocky 198 Posted September 30, 2015 Author Report Share Posted September 30, 2015 thanks lads, will only be setting about 50 so will do like you said and split them into 25s. Quote Link to post
IanB 0 Posted September 30, 2015 Report Share Posted September 30, 2015 How to carry them?? Peg snares on your arm, one arm through the snare loops carrying them, the other to set them. use a bit of string or twine to hang them up when storing them, I normally carry them in bundles of 25, take one off set, move on. When not in use or in the motor stored like this, Woodgas shed. Quote Link to post
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.