slipper 116 Posted August 17, 2015 Report Share Posted August 17, 2015 I bought two boxes of these for my 223 and went out yesterday evening with no wind Set a target at 50 yards and it was two shots through same hole Same at 75 yards, I thought I would check close in case I call a fox right in But at 100 yards it was 1 inch high which I expected but although three shots were through same hole they were half inch to the left How can it be centre at 50 and 75 but slightly left with no wind? Quote Link to post
riohog 5,701 Posted August 17, 2015 Report Share Posted August 17, 2015 it aint rocket science .adjust the scope or its human error!!! 1 Quote Link to post
slipper 116 Posted August 17, 2015 Author Report Share Posted August 17, 2015 I know and thats what I did, what I meant was how can it jump to the left all of a sudden over 25 yards Like bang on at 75 and to the left at 100 with no cross wind? Quote Link to post
shropshire dan 467 Posted August 17, 2015 Report Share Posted August 17, 2015 That is a bit mad init chris. I had great results with this ammo threw my .22-250 but never had this problem. Could you have been clipping a bit of grass or twig or something. Just thinking you changed position and managed to shoot left. Or when you changed position was your rifle rested on uneven ground? Just a couple of thoughts Quote Link to post
slipper 116 Posted August 17, 2015 Author Report Share Posted August 17, 2015 Thats what I thought dan would a bit of grass or similar effect it? Quote Link to post
Skull Hooker 185 Posted August 17, 2015 Report Share Posted August 17, 2015 Grass and twigs would affect trajectory at 100 m. Another thought is whether or not you cleaned your barrel between the 50 and 75 efforts. The slight buildup of crap on the barrel could move the shot at that 100 distance. Quote Link to post
shropshire dan 467 Posted August 17, 2015 Report Share Posted August 17, 2015 Once you adjusted scope at 100 yards did you try it at 50 and 75? Quote Link to post
slipper 116 Posted August 17, 2015 Author Report Share Posted August 17, 2015 No I didnt dan I'm going to try again at the weekend, but the barrel had been thoroughly cleaned before I started; but not between shots Quote Link to post
shropshire dan 467 Posted August 17, 2015 Report Share Posted August 17, 2015 Let us know how ya get on buddy. I collect the new .243 next Tuesday can't wait. I'll be doing some bloody ammo testing aswel. Gonna try 75g first then 80g and also 58g should be fun on the pocket 1 Quote Link to post
bob.243 8,588 Posted August 17, 2015 Report Share Posted August 17, 2015 Was your barrel cooled down for the 100 Yd. test? 1 Quote Link to post
slipper 116 Posted August 17, 2015 Author Report Share Posted August 17, 2015 Must admit it was not completely cool Quote Link to post
hutchey 147 Posted August 18, 2015 Report Share Posted August 18, 2015 Was it cool for the change from 50 to 75? Presuming not. Maybe it's just glanced off something or you might be twitching due to the distance change. Seen that happen loads on the ranges where folks (sometimes me too) are too quick to look up and not stay through the scope and this happens. 1 Quote Link to post
baigon 3 Posted August 18, 2015 Report Share Posted August 18, 2015 Was it cool for the change from 50 to 75? Presuming not. Maybe it's just glanced off something or you might be twitching due to the distance change. Seen that happen loads on the ranges where folks (sometimes me too) are too quick to look up and not stay through the scope and this happens. agreed with you Quote Link to post
Leeboy_1 1 Posted August 18, 2015 Report Share Posted August 18, 2015 Your worried about half inch at 100yrds with factory ammo???? Quote Link to post
CharlieT 32 Posted August 18, 2015 Report Share Posted August 18, 2015 Is there a chance that the rifle was canted slightly to the left. This would produce the results you experienced. 2 Quote Link to post
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.