lpkinz 2 Posted February 11, 2014 Report Share Posted February 11, 2014 I'm new to this and have read a fair amount posted on here so I no you guys can help. I now have my 4z 4" mesh 150 meter long net. I'm going to make a home made quick set setup. I'm using 100% bagging. 2x nets 37.5 yards long. I have started my basket and am now looking at making my poles. I have castration rings on order to attach net to pole. My net 3ft in height. My question is how May poles for each net and how long should they be. If you see anything wrong with my master plan please let me now as knowledge is something I'm looking to gain. Also am I correct in going with 100% bagging? Cheers. 1 Quote Link to post
Hot Meat 3,109 Posted February 11, 2014 Report Share Posted February 11, 2014 3ft in height? is that stretched wide?? im clueless other than settin them an catching with them and lifting them, i set my nets at 18 inch/20 inch high at most, few inch at bottom to go in ground and few inch extra pole above top line for handling, so depending on how high, how much extra you want just buy or make some to suit 2 Quote Link to post
Tiercel 6,986 Posted February 11, 2014 Report Share Posted February 11, 2014 (edited) When you say the net is 3ft high how did you measure it? Its a genuine question just for me to get an idea of what you mean. the rigged by halves part is right that is the nets will be half the stretched length of the net. TC Edited February 11, 2014 by tiercel 2 Quote Link to post
lpkinz 2 Posted February 11, 2014 Author Report Share Posted February 11, 2014 Cheers for getting back. I'll measure the mesh and total height in the morning and get back to you for more assistance. Another question I just thought about is attaching the poles to the net. The end poles will weave through the end mesh but how do you connect the rings to the poles + net. Cheers guys. 1 Quote Link to post
Hot Meat 3,109 Posted February 11, 2014 Report Share Posted February 11, 2014 i think you use a hitch then put band over top?? iv only used quickset and traditional and quickset uses grommits.. 1 Quote Link to post
TOMO 26,045 Posted February 11, 2014 Report Share Posted February 11, 2014 Clove hitch is what you need,,,,,, put the rubber band on first,,, then above it,, loop the clove hitch over the pole, then twist and double your band over the clove hitch,,,, 2 Quote Link to post
Tiercel 6,986 Posted February 11, 2014 Report Share Posted February 11, 2014 As Tomo says, I do the same. First I thread a piece of twine through the C ring then thread it over the pole. Next make a clove hitch with you running lines over the poles. Then you use the piece of twine to pull the ring away from the pole and insert aspoon handle downwards through the gap created. Next twist the spoon handle 180 degrees and lever the loop created over the top of the pole and on to the top of the clove hitch. Pull the spoon handle out and the job is done, all that needs to be done then is wet the pole and slide the ring into the position you want it on the pole. TC 3 Quote Link to post
TOMO 26,045 Posted February 12, 2014 Report Share Posted February 12, 2014 Great pics them for any body to follow,,, I bet the next question is how to tie a clove hitch,,,lol Quote Link to post
lpkinz 2 Posted February 12, 2014 Author Report Share Posted February 12, 2014 That's tidy cheers for them pictures. Tc. Am correct in thinking ill Need to tie the clove hitch as I'm running the run lines through the net? Do you use the same methods to attach the end poles guys? Thanks again. Quote Link to post
lpkinz 2 Posted February 13, 2014 Author Report Share Posted February 13, 2014 I have now part way through the set up. Bagging and poles in position just ready to attach. Do the top and bottom lines need to be tight ish when set up? I'll try post a photo I've taken if I can work out where to attach them? When the poles are attached with the c rings in this way are they moveable? Quote Link to post
Tiercel 6,986 Posted February 14, 2014 Report Share Posted February 14, 2014 (edited) I have now part way through the set up. Bagging and poles in position just ready to attach. Do the top and bottom lines need to be tight ish when set up? I'll try post a photo I've taken if I can work out where to attach them? When the poles are attached with the c rings in this way are they moveable? Do you mean up and down the poles? Yes as long as you wet the pole they will move. If you mean along the lines, then they will not. To add an attachment once you have done the writing scroll down the page and you will see where to make that attachment. TC Edited February 14, 2014 by tiercel Quote Link to post
tjones3862 3,423 Posted February 21, 2014 Report Share Posted February 21, 2014 GO ON GOOGLE,,, AND PUT[ PEGGING ],,,, THAT WILLTELL YOU WHAT LENGTH YOU NEED,,,,,HIT Quote Link to post
lpkinz 2 Posted February 21, 2014 Author Report Share Posted February 21, 2014 find that out after a personal edxasperance I take it? All sorted with the POLES now so will be out Sunday. Quote Link to post
tjones3862 3,423 Posted February 22, 2014 Report Share Posted February 22, 2014 (edited) YOU MITE OF PUT A LOL IN HIT JUST HAVING THE THE CRACK,,,BET YOUR A RIGHT LOAD OF FUN, WHEN YER OUT WITH THE LADS,,,,,,LOL... WILL LOOK FORWARD TO YOUR POST,, AFTER SUNDAYS TRIP,,,, . Edited February 22, 2014 by tjones3862 1 Quote Link to post
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.