huntmark 18 Posted December 9, 2012 Report Share Posted December 9, 2012 When I was a lad I was taught when setting a purse net you put the bottom ring in the hole and then place the net over the hole and peg it at the top. I have noticed a lot of people just spread the net over the hole and peg it. Which would you say works better cheers Quote Link to post
Fat-Ferret 857 Posted December 9, 2012 Report Share Posted December 9, 2012 Doing it the way you were shown might be the best.... Quote Link to post
staffyspen 43 Posted December 9, 2012 Report Share Posted December 9, 2012 I was shown the way you was, I think it helps, starts to purse before the rabbit has left the hole! Thanks Spence Quote Link to post
BazB 37 Posted December 9, 2012 Report Share Posted December 9, 2012 depends on the type of hole for me. if the holes just on the surface with no run in i just spread it around the hole. if not i do it the other way ATB Baz Quote Link to post
Tiny 7 1,694 Posted December 9, 2012 Report Share Posted December 9, 2012 If your way work for you dont change it........ Quote Link to post
huntmark 18 Posted December 9, 2012 Author Report Share Posted December 9, 2012 I was shown the way you was, I think it helps, starts to purse before the rabbit has left the hole! Thanks Spence Quote Link to post
huntmark 18 Posted December 9, 2012 Author Report Share Posted December 9, 2012 Yeah that's what I was thinking Spence. I know it's not always possible to do it but it does work Quote Link to post
Brimmer 220 Posted December 9, 2012 Report Share Posted December 9, 2012 Yep, already pursing around the rabbit before it gets out of the hole has to help, but like Barry said if its just upwards, them spread it around the hole. Quote Link to post
Bunny Boiler 177 Posted December 9, 2012 Report Share Posted December 9, 2012 The reason for your way is that the rabbit steps on the net to prevent it moving, so that the ring that moves purses the net. It means if a rabbit creeps out, instead of bolting fast, it still bags, where as if you just lay it on, it's likely to lift the net if it slowly leaves. I do neither however, I push the ring in to the mud, which acts the same as the rabbit stepping on it and holding it in place. 1 Quote Link to post
bobcullen79 1,495 Posted December 9, 2012 Report Share Posted December 9, 2012 The way you described is probably the most common way, due to the reasons already mentioned. But when you lay a net flat, its normally called back netting. It helps catch the rabbits trying to get back to ground. The net doesnt purse properly, but more so than if the ring was in the hole. Sometimes helps put a few more in the bag. Quote Link to post
huntmark 18 Posted December 9, 2012 Author Report Share Posted December 9, 2012 Cheers lads that was what I was told but keep seeing just spread over so was wondering if the general idea had changed in the last 10 years that I hadn't been ferreting. Thanks happy hunting Quote Link to post
Bunny Boiler 177 Posted December 9, 2012 Report Share Posted December 9, 2012 The way you described is probably the most common way, due to the reasons already mentioned. But when you lay a net flat, its normally called back netting. It helps catch the rabbits trying to get back to ground. The net doesnt purse properly, but more so than if the ring was in the hole. Sometimes helps put a few more in the bag. Like I say. Bury the ring slightly so it holds to the dirt while the sliding ring purses the net, will work in either direction, both back netting and "normal" netting, so instead of having to pick, you can have both reasons rolled into one, and bag EVEN more bunnies. As well as the above reason, burying the ring allows the ferrets to pass through the purse net without disturbing it as much, assuming the ferret can actually fit through the mesh. Atb, BB Quote Link to post
BazB 37 Posted December 9, 2012 Report Share Posted December 9, 2012 The way you described is probably the most common way, due to the reasons already mentioned. But when you lay a net flat, its normally called back netting. It helps catch the rabbits trying to get back to ground. The net doesnt purse properly, but more so than if the ring was in the hole. Sometimes helps put a few more in the bag. Like I say. Bury the ring slightly so it holds to the dirt while the sliding ring purses the net, will work in either direction, both back netting and "normal" netting, so instead of having to pick, you can have both reasons rolled into one, and bag EVEN more bunnies. As well as the above reason, burying the ring allows the ferrets to pass through the purse net without disturbing it as much, assuming the ferret can actually fit through the mesh. Atb, BB i do it this way sometimes if the soil is damp enough and soft enough to hold the ring. aso makes it alot easier in windy conditions atb Baz Quote Link to post
The one 8,511 Posted December 10, 2012 Report Share Posted December 10, 2012 Thats the way i would do it put as much as you can down the hole and spread the rest out round the hole put the peg in so the drawcord tight and the minute the rabbit steps on the net it should be yours , but every holes different and you might have to alter your net setting but as long as your no loosing rabbits does it matter Quote Link to post
Sirius 1,391 Posted December 10, 2012 Report Share Posted December 10, 2012 I guess the more nets you lay the better you get at laying them and what works best in which situation. I have seen them set flat over a hole, end ring in the hole, end ring pushed in the ground, in runs in hedges allsorts. But as long as you catch rabbits don't worry! Quote Link to post
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.