air arms s410 gauge leaking

[steve63 0]

Hi All

Just found my AA s410 is leaking air from the pressure gauge. It is coming from the small drilling in the side of the gauge. Does this mean the seal is worn or do I need to replace the gauge. thanks in advance

 

 

Steve

[Phantom 631]

Welcome to the forum Steve

 

Is it possible that the Guage has worked loose perhapse? Try tightening it buy turning it to the right a little and see if that helps?

 

If not, then someone will be along to help you out further

 

Phantom

[steve63 0]

Welcome to the forum Steve

 

Is it possible that the Guage has worked loose perhapse? Try tightening it buy turning it to the right a little and see if that helps?

 

If not, then someone will be along to help you out further

 

Phantom

[steve63 0]

thanks phantom i will give it a go nothing to loose

 

cheers steve

[davyt63 1,845]

hi steve

is the AA Anti Tamper or pre Anti Tamper?,

if its pre AT then you will be able to take it off and change the seal,but before you do this make sure all the air is out of the cylinder complete!!!

 

if its Anti Tamper then you will have to take it to a gunsmith

or you can drill out the blank your self,and take out the hex screw and chage the seal

 

hope this helps

 

regards

 

davy

[Buster321c 1,010]

Hi All

Just found my AA s410 is leaking air from the pressure gauge. It is coming from the small drilling in the side of the gauge. Does this mean the seal is worn or do I need to replace the gauge. thanks in advance

 

 

Steve

 

 

 

Where about are you Steve ?

[steve63 0]

hi steve

is the AA Anti Tamper or pre Anti Tamper?,

if its pre AT then you will be able to take it off and change the seal,but before you do this make sure all the air is out of the cylinder complete!!!

 

if its Anti Tamper then you will have to take it to a gunsmith

or you can drill out the blank your self,and take out the hex screw and chage the seal

 

hope this helps

 

regards

 

davy

[steve63 0]

Hi Davy

Sorry about the delay in reply, christmas chaos, anyway yes mate its pre A/T so i am going into bagnalls in newcastle tommorrow to get a new seal and give it a go.

 

Thanks mate

 

steve

[steve63 0]

Hi All

Just found my AA s410 is leaking air from the pressure gauge. It is coming from the small drilling in the side of the gauge. Does this mean the seal is worn or do I need to replace the gauge. thanks in advance

 

 

Steve

 

 

 

Where about are you Steve ?

[steve63 0]

I`m up in Gateshead mate

 

steve

[Hagrid 0]

good shoting mate.

[Buster321c 1,010]

There are 3 seals on that `dog leg ` where the guage is mounted .

 

S536

S427

RN219-9

 

All easy enough to install . The S536 can be difficult to allign , as there is a bolt through it , patience is the key .

[davyt63 1,845]

Hi Davy

Sorry about the delay in reply, christmas chaos, anyway yes mate its pre A/T so i am going into bagnalls in newcastle tommorrow to get a new seal and give it a go.

 

Thanks mate

 

steve

 

no problem steve

and take note of buster's advise too!!

 

 

There are 3 seals on that `dog leg ` where the guage is mounted .

 

S536

S427

RN219-9

 

All easy enough to install . The S536 can be difficult to allign , as there is a bolt through it , patience is the key .

 

nice one bustie!!

 

regards

 

davy

[GuyTierney 0]

looks like mine may have the same issue. At first it wouldn't charge at all, but the cocking it before charging helped here. Then when the rifle accepted some air the gage started leaking. I'm yet to take off the stock but this thread look like it will be ultra-useful. Thanks all for sharing.