axsor

[paulk73 151]

got hold of an old axsor today. put my hw silencer on it and scoped it up. tried to zero it. put about 30 pellets through it, and then it went totally awry. it was all over the shop. then pellets where dropping short. was wondering how many shots per refill i should be expecting? and it was not just dropping short they were going well to the right and left. all over really. any ideas what could be causing this and any ideas how to remedy it. cheers.

also on the rifle it just says axsor made in sweden by axsor.

[hunter1989 91]

got hold of an old axsor today. put my hw silencer on it and scoped it up. tried to zero it. put about 30 pellets through it, and then it went totally awry. it was all over the shop. then pellets where dropping short. was wondering how many shots per refill i should be expecting? and it was not just dropping short they were going well to the right and left. all over really. any ideas what could be causing this and any ideas how to remedy it. cheers.

also on the rifle it just says axsor made in sweden by axsor.

 

 

hi paul

 

177 55-70

22 60-

 

atb steve

[paulk73 151]

got hold of an old axsor today. put my hw silencer on it and scoped it up. tried to zero it. put about 30 pellets through it, and then it went totally awry. it was all over the shop. then pellets where dropping short. was wondering how many shots per refill i should be expecting? and it was not just dropping short they were going well to the right and left. all over really. any ideas what could be causing this and any ideas how to remedy it. cheers.

also on the rifle it just says axsor made in sweden by axsor.

 

 

hi paul

 

177 55-70

22 60-

 

atb steve

 

iv not put any wherenear that amout through it mate. i got it second hand. just wondering if theres anything that would make the pressure drop quicker than normal. ie leaking seals or whatever?

[hunter1989 91]

hi paul

 

i got the bsa scorpion a few weeks back and had the same problem but i sent it back,what i would do is when you pull the coocking bolt back listen to see if you can here any air coming out,type in google axsor specs buddy.

[smithie 2,444]

i have a logun axsor and recon its good for 40 shots in 177

[paulk73 151]

cheers guys, i appreciate your replies. im pissed off cos i was meant to be going out tonight after rats. wish id kept the ultra now so at least i would be able to get out and do a bit.

[gazandjen 54]

 

That sucks mate.

 

It must be leaking somewhere. Sounds like the pressure is up and down. That will give erratic shots. If you take it apart make sure it's empty and check some of the seals.

 

...... or take it back

Edited September 25, 2010 by gazandjen

[matt_hooks 188]

It's the Axsor Gemini I would guess.

 

Does it have a threaded adaptor on the end of the barrel that attaches to the air reservoir below? It's the end of the barrel that you screw the mod onto! Mine has a habit of coming loose and turning it into a scatter gun. You need to get an allen key to suit, I think it's a 4mm, but could be less, and make sure it's good and tight. You access the bolt from the charging port.

 

I've never actually counted shots on mine, but I know I can shoot a load of shots before it goes low. Most important thing I've found is not to over charge it, it goes all over the shop if you do that!

 

Can you post a pic of it? They're normally pretty reliable, apart from the loose screw thing, so I'd be interested to see if it is the same gun!

 

Where abouts are you mate?

[paulk73 151]

It's the Axsor Gemini I would guess.

 

Does it have a threaded adaptor on the end of the barrel that attaches to the air reservoir below? It's the end of the barrel that you screw the mod onto! Mine has a habit of coming loose and turning it into a scatter gun. You need to get an allen key to suit, I think it's a 4mm, but could be less, and make sure it's good and tight. You access the bolt from the charging port.

 

I've never actually counted shots on mine, but I know I can shoot a load of shots before it goes low. Most important thing I've found is not to over charge it, it goes all over the shop if you do that!

 

Can you post a pic of it? They're normally pretty reliable, apart from the loose screw thing, so I'd be interested to see if it is the same gun!

 

Where abouts are you mate?

hi mate sounds like its the 1 you said, but cant see the word gemini on it. have tried to tighten the allen key screw, but was already tight, but i have now noticed that there is a tiny bit of play in the barrel, (left to right). just tried to cock it and it is out of air completley. this has to the seals dosnt it?

[paulk73 151]

 

That sucks mate.

 

It must be leaking somewhere. Sounds like the pressure is up and down. That will give erratic shots. If you take it apart make sure it's empty and check some of the seals.

 

...... or take it back

still got out with the terriers, and nailed a load,and got a few with the springer, from out of the rafters in the empty cattle sheds.

[paulk73 151]

 

That sucks mate.

 

It must be leaking somewhere. Sounds like the pressure is up and down. That will give erratic shots. If you take it apart make sure it's empty and check some of the seals.

 

...... or take it back

still got out with the terriers, and nailed a load,and got a few with the springer, from out of the rafters in the empty cattle sheds.

 

think im gonna have to tek it back on saturday.

[matt_hooks 188]

 

That sucks mate.

 

It must be leaking somewhere. Sounds like the pressure is up and down. That will give erratic shots. If you take it apart make sure it's empty and check some of the seals.

 

...... or take it back

still got out with the terriers, and nailed a load,and got a few with the springer, from out of the rafters in the empty cattle sheds.

 

think im gonna have to tek it back on saturday.

 

Not too difficult to strip down and replace the seals, but you need to be sure that it's completely empty before you try to remove the end cap or you will damage the air tube.