hushpower 410

[s horsfield 7]

is it possible to use 3inch carts in a 410 Hushpower.Or would it cause damage to the moderater?

[pest hunter 151 15]

no my mate uses 3inch in his hush power for rabbits so it should be ok for you but im not 100% on that

[eli 0]

is it possible to use 3inch carts in a 410 Hushpower.Or would it cause damage to the moderater?

yeh they are fine use them all time no probs

[Deker 3,478]

is it possible to use 3inch carts in a 410 Hushpower.Or would it cause damage to the moderater?

yeh they are fine use them all time no probs

 

 

I don't have one but I am confident they handle 2.5" and 3" carts.

 

Not sure quite how much sub sonic ammo is available for them but I know Eley do a 3" sub sonic load!

[stubby 175]

use them all the time on my pedretti hushpower, no worries,

 

[eli 0]

use them all the time on my pedretti hushpower, no worries,

 

stubbey do you find yours hard to clean onley mines a ba..ted to undo at times wie mod being a tight fit

[unclemicky 3]

is it possible to use 3inch carts in a 410 Hushpower.Or would it cause damage to the moderater?

 

 

410 500 Hushpower Mossburg 3inch no problem , try not to use the 2inch as they jam , hope this helps .

[stubby 175]

use them all the time on my pedretti hushpower, no worries,

 

stubbey do you find yours hard to clean onley mines a ba..ted to undo at times wie mod being a tight fit

 

 

my 410 un-screws no problem, keep a bit of copper grease on it to stop it from sticking, I also had a 12 bore in the same model, now that was a bar steward and wouldent unscrew

I also use 2" sub sonics for fox dispatch, never had a problem with sticking

[unclemicky 3]

Stubby my Mossburg is a pump action an the 2 inch dont want to cycle as nice as the longer carts , it's the same as my hatsan does not like 65mm , but cycles anything 67.5 upwards , "SIZE MATTERS" lol

[s horsfield 7]

cheers lads i'll try a box of 3inch and see how i get on ,anyone recomend a make or just grab a box?

[stubby 175]

cheers lads i'll try a box of 3inch and see how i get on ,anyone recomend a make or just grab a box?

 

 

got to be ELEY all the way, fibre wads are better than plastic in a hushpower

[eli 0]

use them all the time on my pedretti hushpower, no worries,

 

stubbey do you find yours hard to clean onley mines a ba..ted to undo at times wie mod being a tight fit

 

 

my 410 un-screws no problem, keep a bit of copper grease on it to stop it from sticking, I also had a 12 bore in the same model, now that was a bar steward and wouldent unscrew

I also use 2" sub sonics for fox dispatch, never had a problem with sticking

thanks stubbey will do you just get pissed with rice nosise in mod from time to time

[jackinbox99 41]

Depends on what your gun is proofed for!

 

Ive the mossberg pump hushpower 410 and as the picture someone else posted shows, its proofed for 3inch. I use ELEY 3inch normal & subsonic loads in it.

[slingshot 0]

As long as the gun is proofed for 3 inch there will be no problem. Use a BoreSnake to clean the barrel , that way you do not have to strip the moderater. 3 inch eley subs are crap, just use the normal 3 inch, there is no difference in noise level and you again an extra 5 yards in range . Avoid full length plastic wad cartridge like winchesters as the wad can get stuck in the baffles and damage them. :headshot::

is it possible to use 3inch carts in a 410 Hushpower.Or would it cause damage to the moderater?

Edited March 29, 2010 by slingshot

[s horsfield 7]

cheers slingshot i'll try the eley's 3inch then.