connor bsa ultra multi 0 Posted July 30, 2009 Report Share Posted July 30, 2009 the sheet that come with the rifle says undo the restrictor screw or remove using the allen key provided , but there is no restrictor screw can any 1 help Quote Link to post
Guest buster321c Posted July 30, 2009 Report Share Posted July 30, 2009 What you on about mate ????? Quote Link to post
connor bsa ultra multi 0 Posted July 30, 2009 Author Report Share Posted July 30, 2009 What you on about mate ????? says you have to take it off or summit to fill it be a hand pump Quote Link to post
Guest buster321c Posted July 30, 2009 Report Share Posted July 30, 2009 Do not over charge the rifle as this may be dangerous. Doing so will reduce the power and can damage the rifle. A filling adaptor is supplied with each rifle; this has a restrictor screw fitted which must be screwed tightly in place when using an air tank to fill the gun, or the rifle could be damaged. If using a hand pump the restrictor screw should be loosened or removed using the Allen key provided • Before filling, always ensure the gun is unloaded and the safety catch is on. • Unscrew the end cap from the front of the air reservoir. • If the air reservoir is empty, cock the rifle • Insert the filling adaptor into the filling port, and push it home. • Make sure the bleed screw on the charging unit is closed, and then open the air bottle valve slowly. • Slowly fill the gun to the maximum recommended charge pressure, and close the valve. Allow a few minutes for the pressure to settle, and then, if needed, top up the pressure in the gun, and close the valve again. • Quickly open the air bleed valve on the charging unit to allow the air in the hose to escape. • Pull the filling adaptor from the filling port and replace the end cap. • Remember that your rifle may be cocked, if it is you should de-cock it immediately for safety reasons. • To de-cock your rifle, push the cocking knob in and hold firmly, pull trigger and slowly release the knob until it is back in the rest position. Regularly check the condition of the filling probe “O†rings and apply a little Molycote 111 grease. Only use this grease on the “O†rings as automotive mineral oils and grease can cause an explosion if used with high-pressure air. Quote Link to post
connor bsa ultra multi 0 Posted July 30, 2009 Author Report Share Posted July 30, 2009 (edited) Do not over charge the rifle as this may be dangerous.Doing so will reduce the power and can damage the rifle. A filling adaptor is supplied with each rifle; this has a restrictor screw fitted which must be screwed tightly in place when using an air tank to fill the gun, or the rifle could be damaged. If using a hand pump the restrictor screw should be loosened or removed using the Allen key provided • Before filling, always ensure the gun is unloaded and the safety catch is on. • Unscrew the end cap from the front of the air reservoir. • If the air reservoir is empty, cock the rifle • Insert the filling adaptor into the filling port, and push it home. • Make sure the bleed screw on the charging unit is closed, and then open the air bottle valve slowly. • Slowly fill the gun to the maximum recommended charge pressure, and close the valve. Allow a few minutes for the pressure to settle, and then, if needed, top up the pressure in the gun, and close the valve again. • Quickly open the air bleed valve on the charging unit to allow the air in the hose to escape. • Pull the filling adaptor from the filling port and replace the end cap. • Remember that your rifle may be cocked, if it is you should de-cock it immediately for safety reasons. • To de-cock your rifle, push the cocking knob in and hold firmly, pull trigger and slowly release the knob until it is back in the rest position. Regularly check the condition of the filling probe “O†rings and apply a little Molycote 111 grease. Only use this grease on the “O†rings as automotive mineral oils and grease can cause an explosion if used with high-pressure air. thats the bit a dont understand ]b]. If using a hand pump the restrictor screw should be loosened or removed using the Allen key provided[/b][/color] Edited July 30, 2009 by connor bsa ultra multi Quote Link to post
just jack 998 Posted July 30, 2009 Report Share Posted July 30, 2009 good going busty, feck that, i'm off back to a springer me thinks Quote Link to post
connor bsa ultra multi 0 Posted July 30, 2009 Author Report Share Posted July 30, 2009 thats the bit a dont understand . If using a hand pump the restrictor screw should be loosened or removed using the Allen key provided Quote Link to post
Guest buster321c Posted July 30, 2009 Report Share Posted July 30, 2009 A filling adaptor is supplied with each rifle; this has a restrictor screw fitted which must be screwed tightly in place when using an air tank to fill the gun, or the rifle could be damaged. If using a hand pump the restrictor screw should be loosened or removed using the Allen key provided AS im reading it , i assume it refers to a grub screw in the adapter itself ? I do have this gun , but as it was second hand , and only ever been filled with a bottle i don`t know . Sorry . Quote Link to post
Guest buster321c Posted July 30, 2009 Report Share Posted July 30, 2009 I have a solution , incomming PM Quote Link to post
connor bsa ultra multi 0 Posted July 30, 2009 Author Report Share Posted July 30, 2009 A filling adaptor is supplied with each rifle; this has a restrictor screw fittedwhich must be screwed tightly in place when using an air tank to fill the gun, or the rifle could be damaged. If using a hand pump the restrictor screw should be loosened or removed using the Allen key provided AS im reading it , i assume it refers to a grub screw in the adapter itself ? I do have this gun , but as it was second hand , and only ever been filled with a bottle i don`t know . Sorry . there is no Allen bolt to loosen Quote Link to post
connor bsa ultra multi 0 Posted July 30, 2009 Author Report Share Posted July 30, 2009 A filling adaptor is supplied with each rifle; this has a restrictor screw fittedwhich must be screwed tightly in place when using an air tank to fill the gun, or the rifle could be damaged. If using a hand pump the restrictor screw should be loosened or removed using the Allen key provided AS im reading it , i assume it refers to a grub screw in the adapter itself ? I do have this gun , but as it was second hand , and only ever been filled with a bottle i don`t know . Sorry . there is no Allen bolt to loosen it pumps up ok though Quote Link to post
Guest buster321c Posted July 30, 2009 Report Share Posted July 30, 2009 The adaptor which plugs into the rifle has a small screw which acts as a restrictor if you fill from a bottle. If you use a pump, it should be unscrewed. You can only get at it when the adaptor is off the hose. Quote Link to post
just jack 998 Posted July 30, 2009 Report Share Posted July 30, 2009 put some pics up to show the lad, twat Quote Link to post
Guest buster321c Posted July 30, 2009 Report Share Posted July 30, 2009 sithee , watch it cock Quote Link to post
Guest buster321c Posted July 31, 2009 Report Share Posted July 31, 2009 The sacred restrictor screw Quote Link to post
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.