burkey 1 Posted May 14, 2009 Report Share Posted May 14, 2009 I would like to make my own lure coursing rollers & lure Machines would any body know what motor, controller and battery to use, as I need one foe my lurcher and harris's. Regards, Si. Quote Link to post Share on other sites
tango 221 Posted May 14, 2009 Report Share Posted May 14, 2009 I would like to make my own lure coursing rollers & lure Machines would any body know what motor, controller and battery to use, as I need one foe my lurcher and harris's. Regards, Si. easy donne if you can weld,,,all you need is a starter from a car(one without the cone over the shaft)an old golf or polo has one, mount it in a frame starter at the front wheels at the back,try to get a starter with a built in selinoid,if you can get your hands on a steel wheelbarrow rim knock out the center shaft and spot weld on to the staft only spot it on as to much heat will feck the starter ,take your two wires from the starter and fit termanals,take a smaller wire from the selinoid power and fit a push button swicth on the end ,,,stick a battery in an away you go i will try an get pics up later as these would explain better Quote Link to post Share on other sites
hardcorehunter 0 Posted May 17, 2009 Report Share Posted May 17, 2009 (edited) Just an idea bud but how does a washing machine motor & a dimmer switch sound Edited May 17, 2009 by hardcorehunter Quote Link to post Share on other sites
burkey 1 Posted May 18, 2009 Author Report Share Posted May 18, 2009 I would like to make my own lure coursing rollers & lure Machines would any body know what motor, controller and battery to use, as I need one foe my lurcher and harris's. Regards, Si. easy donne if you can weld,,,all you need is a starter from a car(one without the cone over the shaft)an old golf or polo has one, mount it in a frame starter at the front wheels at the back,try to get a starter with a built in selinoid,if you can get your hands on a steel wheelbarrow rim knock out the center shaft and spot weld on to the staft only spot it on as to much heat will feck the starter ,take your two wires from the starter and fit termanals,take a smaller wire from the selinoid power and fit a push button swicth on the end ,,,stick a battery in an away you go i will try an get pics up later as these would explain better Thank you very much for your help I will try this still not really shore about the wires bit mite become clear after I have seen the starter close up!!!! Regards, Si. Quote Link to post Share on other sites
patdahat 41 Posted May 18, 2009 Report Share Posted May 18, 2009 the one my neighbour had was the geardox off a rear wheel drive car, it had a handle on the side which whould have been turning the drive shaft and just a bracket on the opp side to gather the string, all was monuted on a frame and could change the gears for different speeds, no bother to pull out the string again just pop it into nuteral, only thing is its a two person job 1 to wind and a slipper. Quote Link to post Share on other sites
ferreter.al 22 Posted May 18, 2009 Report Share Posted May 18, 2009 I would like to make my own lure coursing rollers & lure Machines would any body know what motor, controller and battery to use, as I need one foe my lurcher and harris's. Regards, Si. good question,i have been meaning to put this poste up.nice one.atb Quote Link to post Share on other sites
tango 221 Posted May 18, 2009 Report Share Posted May 18, 2009 Just an idea bud but how does a washing machine motor & a dimmer switch sound WASHING MOTOR ID 240VOLT MATE SO UNLESS YOU COULD RUN AN 240 LEAD FROM A PLUG TO YOUR POSITION THEN IT WOULDNT DO THE JOB WITH OUT AN INVERTER BUT IN THEORY IF YOU COULD THEN IT IS POSSIABLE Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.